SimNet Cable 2MSimNet (Simrad Intelligent Marine Network) is a unique marine electronics network system. Over the last 5 years, it has proven to be one of the most reliable and easy to use networks in the marine industry. SimNet is easy to install with thin cables and small plugs.

Verado Hydraulic KitKit Includes:(1) Return hose 1, 9M(6') 3/8"ID with SAE 5/8"IR coupling(2) Tee-4-ORFS: ORFS 04 x ORFS 04 x SAE 7/16"-20 UNF(1)Tee-fitting with 3/8" barbs for return hose connection(1) SAE 5/8"-18-7/16"-20 UNF Flare for pump unit return(3) Non-Corrosive hose clamps, 5/16-9/16"

Mercury Verado Hose - 6' PairProduct DetailsProduct Dimensions: 14" x 13" x 5"Weight: 1.8lb

Simrad SimNet Product to NMEA 2000 Network Adapter CableThe Simrad SimNet Product to NMEA 2000® Network Adapter Cable, manufactured by Simrad, is used to connect a Simrad SimNet product like the NMEA 2000®/NMEA 0183 Adapter (AT10) or CX NavStation Series products to an NMEA 2000® network as shown in the following diagram. The cable is 0.5 meters in length and has a female SimNet connector on one end and a standard male NMEA 2000® Micro Series connector on the other end.

DST800 Plastic Thru Hull Transducer 235khz N2k Simrad's DST800 active D/S/T TH plastic 235 kHz transducer with 2 m (7 ft) cable.

SimNet Cable 5MSimNet (Simrad Intelligent Marine Network) is a unique marine electronics network system. Over the last 5 years, it has proven to be one of the most reliable and easy to use networks in the marine industry. SimNet is easy to install with thin cables and small plugs.

AT10HD SimNet to NMEA 0183 Coverter f/ 10Hz HeadingAT10HD Universal high speed NMEA0183 converter MFG 24006694 converts NMEA0183 10Hz heading data to Simnet.

SimNet T Jointer - 3PSimrad SimNet T Jointer - 3PBrand NewThe Simrad 24005860 is a SimNet(Simrad Intelligent Marine Network) t jointer with 3 prong.

SimNet Cable 10MSimNet (Simrad Intelligent Marine Network) is a unique marine electronics network system. Over the last 5 years, it has proven to be one of the most reliable and easy to use networks in the marine industry. SimNet is easy to install with thin cables and small plugs.

AT10The AT10 converts data on NMEA0183 format to SimNet/ NMEA2000 format and vice versa. AT10 is powered from the SimNet bus or from the NMEA2000 bus via an adaptor cable.Note: The AT10 complies with NMEA0183 version 3.01.

Simrad adapter cable, Ethernet Yellow 5 pin male to RJ45 female 2 m (6.5 ft)*needed when hooking up a WM-2 to a NSE series

Simnet 7 Prong Multi-Joiner

Simnet Protection Plug

Broadband 3G™ Radar with 20M CableFaster, better, longer...Join the Broadband Radar™ revolution for superior short-range target detection and unrivalled target separation.Features:Crystal Clear ImagesZero Radiation HazardInstantOn™Low Power ConsumptionMount AnywhereQuick InstallationUnrivalled Short-Range Performance10 MARPA TargetsNow with 30% more rangeBroadband 3G™ Radar allows you to see more targets farther away from your boat. Now you get the same impressive short-r

Broadband 4G Radar with 20m CablePart #: 000-10421-001Simrad's revolutionary Broadband 4GT Radar offers all of the benefits of the Broadband 3G Radar, including a true 200' working range, plus some spectacular extra features. The Broadband 4G has an impressive 50% improvement in range and target detection capability with a new 36 nautical mile range and 18 range scales to accommodate the increased performance. Broadband 4G is the first dome antenna to employ beamsharpening. This technology enabl

Simrad Power Cable f/NSE NSS & StructureScan 3D, GO7, GO9, GO124 pin conn. to 4 bare wires for power in - power control bus and external alarm - 6.5 ft (2 m).

AP70 PackAP70 Pack Includes: (AP70, AC70, RF300, without heading sensor)Match Your RequirementsThe Simrad AP70 is ideal for both simple installations where IMO approval is not required but also can be configured (by matching with an approved computer) to meet the requirements for a Type Approved autopilot. Install as a stand-alone display or network as a second or third station for ultimate vessel control.Smart ConstructionThe AP70's stunning waterproof design, daylight viewable display, color u

Micro-C Female to SimNet Cable Simrad's Micro-C Female to SimNet 1M Cable

Transom Mounting Bracket for P66 Transducer - 2004 & up

SimNet Cable 1 FootSimNet (Simrad Intelligent Marine Network) is a unique marine electronics network system. Over the last 5 years, it has proven to be one of the most reliable and easy to use networks in the marine industry. SimNet is easy to install with thin cables and small plugs.

RF25N Rudder Feedback w/Link & Micro-C Cable - 5MThe RF25 is a medium duty rudder feedback unit with Micro-C interface. The RF25 will attach directly to industry standard Micro-C systems for straight-forward installation.Features:+/- 120° MeasurementPrecise and Accurate; +/- 0.5°Micro-C Connectivity5.5M attached Micro-C Cable

NSE/NSS Video/Data cableNSE / NSS Video/Comms Cable (8 pin conn. to bare wires for NMEA and 2 RCA female for Video in Port one and two) 2M (6.5')

N2K Starter KitNMEA 2000 Network Starter Kit Includes:Network power cable4.5M (15') N2K cable3 x T-connectors2 x network terminators

117WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on 2" bronze and stainless steel housings.You can use wrench 117WR-4 to brace the housing when using this wrench.For use with:B117 B150 B744V B744VL B765C SS555

60WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on 2" bronze and stainless steel housings. You can use wrench 60WR-4 to brace the housing when using this wrench.For use with:B60SS60

75WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on bronze and stainless steel housings. You can use wrench 75WR-4 to brace the housing when using this wrench.For use with:B75SS75

164WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on B164, SS164 and SS264 housings.You can use wrench 164WR-4 to brace the housing when using this wrench.For use with:B164SS164SS264

117WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the side of the housing to facilitate tightening of the hull nut. For 2" bronze and stainless steel housings (P617V, B617V, SS617V).Use wrench 117WR-2 or 117WR-3 for the hull nut.*Note that this wrench will not fit on the CA500 camera housing.

60WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the side of the housing to facilitate tightening of the hull nut.Use wrench 60WR-2 or 60WR-3 for the hull nut.For use with:B60SS60

75WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the side of the housing to facilitate tightening of the hull nut. Use wrench 75WR-2 or 75WR-3 for the hull nut.For use with:B75SS75

175WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the top of the housing to facilitate tightening of the hull nut. Use wrench 164WR-2 or 164WR-3 for the hull nut.For use with:B164B175SS164SS264IMPORTANT: the design of the housing for these transducers changed slightly in June 2012. This wrench is for the newer design and has an internal width of 2-3/4". If you need a wrench for the older designs then use the 164WR-4 instead,

117WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations.For use with:B117B150B744VB744VLB765CSS555

60WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations.For use with:SS60B60

75WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations.For use with:B75SS75

164WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations.For use with:B164SS164B175CSS164

117WR-3 Double Handle Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations.For use with:B117B150B744VB744VLB765CSS555

60WR-3 Double Handle Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations.For use with:B60SS60

75WR-3 Double Handle Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations.For use with:B75SS75

164WR-3 Double Handle Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut. Wrenches are constructed of 3/16" thick mild steel. They can easily be bent or modified to accommodate challenging installation locations.For use with:B164SS164B175CSS264

RI-12 Radar Interface ModuleFeatures:Designed to accomodate either 12 or 24 colt systems and used for all Halo modelsRugged, screw-in power connector block (DC cable not supplied)Supplies 36V DC to the pedestal in Tx mode - Status LED is Green when on - Red when notEasy to connect NMEA2000 Micro CEthernet 10_100BaseT output with Ethernet LED (pigtail adapter supplied for internal RJ45 to external Navico Yellow)Easy removable access cover with captive screwsSilicon Rubber Cable glandsComes with:N